Electrolux E36GF76GPS Poradnik Użytkowania i Eksploatacji

318201761E30GF74GPS E36GF75GPS E36GF76GPS

10Preparing for InstallationCABINET AND COUNTERTOP PREPARATIONNONONONONOTESTESTESTESTES• If cabinet storage space is to be provided directly above the

11Preparing for installationGENERAL DIMENSIONSPlan the installation so that the electrical connection, gas shut-off valve, and pressureregulator are a

12Preparing for InstallationGENERAL DIMENSIONS

13Preparing for InstallationWOOD/COMPOSITE OVERLAY INSTALLATIONThe bottom of an overhead hood should be 30” minimum to 36” above thecountertop. This

14INSTALLING THE ANTI-TIP BRACKETInstallation FIG. 3** **Note: I

15Figure 3Backguard Installation(36" range shown)BackguardWARNINGWARNINGWARNINGWARNINGWARNINGBe sure the range is not connected to gas or power b

16WARNINGWARNINGWARNINGWARNINGWARNINGDo not attempt to disengage the hinge catches with the door removed from the oven. The hingesprings could release

17Installation1 The range is equipped with a three-prong power cord (grounding plug which mateswith a standard three-prong grounding wall receptacle t

18InstallationCONNECT RANGE TO GAS SUPPLYINSTALLING THE RANGEMeasure from the floor to the countertop and adjust the leveling legs as required to posi

19WARNINGWARNINGWARNINGWARNINGWARNING• The range and shut-off valve must be disconnected from the gas supply piping during anypressure testing exceedi

2Finding InformationREAD AND SAVE THESE INSTRUCTIONSRead all instructions before installing the range.For your safety, please read and observe all saf

20OperationTO ENSURE PROPER AND SAFE OPERATION• Read all instructions before using this appliance. Install or locate the appliance only inaccordance

21INSTALLATION AND SERVICES MUST BE PERFORMED BYA QUALIFIED INSTALLER.IMPORTANT: SAVE FOR THE LOCAL ELECTRICAL INSPECTOR’S USE.READ AND SAVE THESE INS

22IMPORIMPORIMPORIMPORIMPORTTTTTANTANTANTANTANTAfter replacing the natural gas to LP orifices, be sure to keep the original factoryinstalled natural g

23HOW TO CONVERT THE RANGE FOR USE WITHLP/PROPANE GASWARNINGWARNINGWARNINGWARNINGWARNINGa. Electrical shock hazard can occur and result in injury or d

24a. Remove top grates, burner caps and inner burner rings.b. Lift off outer burner heads and burner bases.c. Remove the factory installed natural gas

25a. Remove the toe kick panel.b. Remove the two (2) screws on the bottom of the toe kick panel. Hold the bottom edge of toe kick panel at the mid

26a. Remove back cover (See Fig. a)b. Using an adjustable wrench, remove the orifice from the orifice holder. Replace with oven broiler orifice siz

27Conversion To LP Gasa. Remove back cover (See “Fig. a” on previous page)b. Carefully remove the griddle plate using caution as the plate is very h

28 CONVERT GAS VALVES FOR LP/PROPANE GASa. Remove control knobs, bezel and control panel.b. Using a flat screwdriver, replace main burner bypass jet

29Conversion To LP GasRECONNECT GAS AND ELECTRICAL SUPPLY TORANGELeak testing of the appliance shall be conducted according to the installationinstruc

3Finding InformationTABLE OF CONTENTSPlease Read And Save This Guide ... 2Questions ...

30AIR SHUTTER OVEN BURNERThe air shutter for the oven burner may need adjustment, especially if the unit hasbeen converted for use with LP/Propane gas

4SafetyIMPORTANT SAFETY INSTRUCTIONS

5SafetySAFETY PRECAUTIONS

6SafetyWARNINGWARNINGWARNINGWARNINGWARNINGNever use this appliance as a space heater to heat or warm a room. Doing so may result in carbonmonoxide poi

7NONONONONOTETETETETEThis range is shipped from the factory pre-set for use with natural gas. For LP conversion see theaccompanying LP Conversion Kit.

8Preparing for InstallationELECTRICAL POWER SUPPLY REQUIREMENTSIt is the owner’s responsibility to ensure that the electrical connectionof this applia

9Preparing for InstallationGAS AND ELECTRICAL ROUGH-INLocationsA manual shut valve must be installed in the gas piping, external to theappliance, for